Epoxy Grout for Tile: Where It Wins and How to Install It

Consider epoxy grout when tile joints will see constant water, stains or heavy traffic. That includes showers, kitchen floors, mudrooms, commercial kitchens, entries and lobbies. This two- or three-part resin system cures into a dense, non-porous joint that doesn’t take in water or stains like cement grout. Your installer has more to manage, though: working time is short, cleanup timing matters, and certain joints must stay epoxy-free. Here’s what to know about choosing, installing and specifying it for a home or commercial building in the Northwest and northern Rockies.
TL;DR
- Epoxy grout is made of epoxy resins and a filler powder. The Tile Council of North America (TCNA) calls it extremely hard, durable and nearly stainproof when it meets ANSI A118.3.
- It suits floors, showers, kitchens, entries and high-traffic commercial areas, and it does not need sealing.
- Installation is a race against the clock: small batches, firm packing, timed cleanup and a full cure before heavy use.
- Never put it in movement joints such as corners and change-of-plane joints. Those get flexible sealant.
- Choose the grout, color and setting materials together, before tile is ordered.
Table of Contents
- What epoxy grout actually is
- Where epoxy grout earns its place
- Where epoxy grout does not belong: movement joints
- The substrate decides how long the joints last
- How to install epoxy grout, step by step
- Caring for epoxy grout
- Color, tile and stairs
- Specifying epoxy grout on commercial projects
- Our perspective
- Get the tile, grout and setting materials from one place
- FAQ
- Sources
What epoxy grout actually is
Cement grout is a cement-and-sand powder mixed with water or a liquid polymer. Epoxy grout is different chemistry. TCNA describes epoxy grout that meets ANSI A118.3 as made from epoxy resins and a filler powder, and notes that the bond between tiles is often stronger than the tile itself. ANSI A118.3 is the American national standard that epoxy tile grouts are tested against, so it’s the line to look for on a data sheet.
The practical differences come from that chemistry:
- Hardening. Epoxy cures by a chemical reaction between resin and hardener, not by water evaporating. That is why it behaves so differently once set.
- Porosity. A two-component epoxy is non-porous and does not usually require sealing, while cement grout absorbs water and needs periodic sealing. One manufacturer’s FAQ puts epoxy absorption below 0.5%, and says its epoxy grouts never require sealing.
- Handling. TCNA notes epoxy is harder to use and shape than cementitious grout, has a more plastic look, may slump as it warms and cures, and generally takes longer to reach full cure.
- Material cost. Epoxy costs more than cement grout per bag, which is why it is specified where its performance pays back. We do not publish prices, and we quote every job in writing.
So can you use epoxy instead of grout between tiles? Yes. Epoxy grout is a grout. You’re replacing a cement joint with a resin joint, not adding a coating to an existing one.
Where epoxy grout earns its place
Floors
Epoxy is a strong answer for floor joints. One major manufacturer’s data sheet lists most ceramic, porcelain and quarry tile, pavers and natural stone for interior residential and commercial floors and walls, exterior residential and commercial floors, and heavy-traffic areas such as transit stations, malls and airport terminals. For a homeowner, the floors that benefit most are the ones that get wet, dirty and walked on daily:
- Kitchens, where grease and spilled juice stain cement joints.
- Mudrooms and entries. Our winter-ready mudroom tile guide explains why the entry takes the worst of a Montana winter: meltwater, de-icer and grit.
- Bathrooms and laundry rooms, where waterproof flooring decisions start with the joint.
- Radiant-heated tile floors, where a dense joint that does not absorb moisture keeps its color.
Showers and wet walls
In showers, the grout joint is the part of the system that sees water every day. A non-porous joint resists mold and mildew staining because there’s nothing for moisture to soak into. If you’re planning a tiled shower, our shower floor tile page shows the small-format tiles that have the most joints, which is exactly where epoxy pays off. Our bathroom remodel tile guide covers the rest of the selection.
Commercial kitchens, lobbies and exteriors
For property managers and specifiers, the case is about lifecycle. Epoxy resists chemicals, standing water and repeated cleaning, which is why it appears in restaurant kitchens, hospitality back-of-house areas, retail entries and pool surrounds. Epoxy grout’s resistance to harsh weather also makes it suitable for outdoor use. If you’re specifying porcelain for a patio, pair it with our outdoor patio tile guide.
Use the product that matches the environment. One manufacturer’s premium epoxy data sheet states it isn’t for areas exposed to harsh chemicals or aggressive cleaning such as steam cleaning, and not for veterinary clinic or kennel floors, so a kitchen with a chemical-heavy sanitation program should get an industrial-grade epoxy written into the spec. That’s a conversation to have with your supplier before the order, not after.
Where epoxy grout does not belong: movement joints
This is the answer to “will epoxy grout crack?” Properly installed in the field of the tile, it’s rigid and resists cracking and shrinking. Rigid is also the catch. TCNA detail EJ171 calls for movement joints at wall-to-wall corners, wall-to-floor transitions and wall-to-ceiling joints to be kept free of grout and filled with flexible sealant. Epoxy cures rigidly and locks adjacent surfaces together, so building movement can transfer stress into the tile and crack or debond it.
The rule, in plain terms:
- Grout the field joints between tiles with epoxy.
- Fill the corners and the floor-to-wall change of plane with a color-matched flexible sealant.
- Honor the movement joints that continue through large tile areas, especially in commercial floors.
That isn’t a limit on epoxy. It’s how a tile assembly is built to last, and it matters most in Montana, where temperature swings and seasonal humidity move framing more than people expect.
The substrate decides how long the joints last
A grout joint is only as stable as what sits under it. Wood subfloors need to be stiff enough for tile. One epoxy mortar-and-grout data sheet requires a maximum joist spacing of 16 inches on center and exterior-grade plywood underlayment when applied over plywood, and it is not intended for plywood in exterior, wet interior or heavy commercial applications. In a commercial building, the same logic applies to slabs. If a slab is cracked or spalled, it needs repair before anything is set on it, and a guide to commercial concrete repair methods is a useful way to understand what that work involves. For new builds, our new construction flooring timing guide explains where tile fits in the schedule so slabs have time to cure and dry.
How to install epoxy grout, step by step
Epoxy grouting is learnable, but it’s less forgiving than cement grout. Here is the sequence, with the point at each step where jobs go wrong.
1. Confirm the setting bed is ready
The tile must be firmly set before grouting. One data sheet restricts foot traffic until the tile is firmly set, about 12 hours, begins grouting after 24 hours, and allows 48 hours before grouting over cement mortar. Always follow the data sheet for the specific setting material you used. Joints should be clean, empty and dry, with spacers removed and thinset cleared from the joint depth. This is where choosing setting materials and grout together helps, and it’s why our setting materials shop carries them side by side.
2. Stage everything before you mix
Plan to grout only an area you can comfortably finish in about 20 minutes, have every tool ready before mixing, and mix each component separately before combining them. Have a bucket of clean water, a firm epoxy float with a sharp edge, white nylon scouring pads and more sponges than seems necessary. Epoxy clogs sponges quickly, and the same guide notes that it isn’t forgiving on clothing. Wear nitrile gloves and ventilate the room.

3. Mix the components in order
The standard three-part kits work like this: pour the liquid Part A and Part B into a clean, dry pail, mix, then add the Part C powder and mix. Mix full units only. Splitting a kit by eye risks an off-ratio batch that never cures properly. Temperature matters too: one manufacturer lists an optimum curing temperature of 73°F (23°C). In an unheated Montana building shell in winter, that’s a real consideration. Heat the space before and during the job.
4. Pack the joints
Spread the grout and pack it diagonally across the joints with a firm, sharp-edged rubber float held at about 90 degrees. Force it in continuously so there are no voids. A joint filled only at the surface is the most common failure we see described in installation guides, because the void underneath collects water. Then remove excess by dragging the float diagonally across the tile before the grout loses plasticity.
5. Clean on the clock
Cleanup is the step that decides the result. The usual instruction is to wait about 20 minutes, then clean with the supplied additive in 2 gallons of water, wiping in a light circular motion and then diagonally with a clean sponge. Repeat about an hour later with the second additive packet, as described in the manufacturer’s FAQ. Water is your friend here. Too little water pulls grout out of the joints. Another manufacturer calls for a white nylon scouring pad and cold water, and warns that stepping on freshly cleaned tile could permanently damage the grout.
The next day, a paint scraper takes off remaining residue and an epoxy haze remover handles any film. Never use acid cleaners on epoxy. One data sheet warns they cause irreversible damage to the grout or tile.
6. Protect it while it cures
Curing takes longer than the grout feels like it needs. One manufacturer’s instructions call for protecting the installation for at least 7 days, waiting at least 3 days before checking hardness, keeping traffic off for at least 24 hours after setting, and allowing at least 3 days of curing before routine cleaning. Another lists maximum stain protection at seven days at 70°F, and full-service conditions at 10 days. Check the data sheet for the exact product you’re using and schedule the job so the space isn’t needed before then. On commercial work, that means writing the cure window into the turnover schedule.

Where we take work off your hands
We supply the setting materials and grout for this process through our pro shop, and we help match them to the tile and the room. For builders and property managers, our commercial procurement desk provides detailed written quotes, trade programs and logistics support, so the grout, the tile and the delivery date arrive aligned with your install crew.
Caring for epoxy grout
Maintenance is simple, which is much of the point. Allow it to cure fully for 3 days before regular cleaning, then use a neutral-pH cleaner followed by a clean-water rinse and avoid harsh chemical cleaners. If you use a steam cleaner, one manufacturer says to keep the wand 6 to 12 inches (15 to 30 cm) above the surface, and to rinse away fatty residue so it doesn’t sit on the grout. Sealing the grout is unnecessary. If the tile or stone itself needs a sealer, wait for the grout to fully cure first, which one manufacturer puts at 10 days at 70°F. Our pro shop stocks stains, sealers and topcoats for stone and finished surfaces when you reach that stage.
Color, tile and stairs
Epoxy sets a color for the life of the installation, so choose it with the tile in hand. Mid-tone shades tend to look cleaner longer on floors than pure whites, and the plastic sheen of epoxy can make uneven tile edges easier to see, which is one more reason to use tile with consistent edges and a joint width suited to the tile. Our grout colors page lays out the manufacturer color charts we work from, and our epoxy grout page covers when to use it and how it compares with other grouts. If you’re weighing tile types, start with porcelain versus ceramic, and for a different look at the choice, see tile versus luxury vinyl.
Tiled stairs deserve a separate mention. Risers and treads take impact and moisture at the edge, so the transition to the nosing matters as much as the grout. For stair treads and nosing, Tread Space is the place to look, and we can coordinate the tile and grout choice around the profile you pick.
Specifying epoxy grout on commercial projects
For architects, designers and general contractors working across the Northwest, a short spec checklist avoids most field problems:
- Name the standard: ANSI A118.3 for epoxy grout.
- Name the area. Wet floors, kitchens and entries get epoxy, and corners and movement joints get flexible sealant.
- Name the cleaning regimen. If the owner steam-cleans or uses aggressive chemicals, choose the grade of epoxy built for it.
- Name the cure window and who protects the floor during it.
- Name the tile. Soft polished marble and delicate glazed or glass tile can scratch during installation, so a small test area comes first.
- Order grout, setting materials and tile from the same source so lots, colors and delivery dates match.
Our commercial procurement page explains how we support contractors and specifiers in Montana, Idaho, Washington, Oregon, Wyoming and the Dakotas.
Our perspective
Most grout problems we hear about trace back to a decision made late. The tile was chosen first, the grout was an afterthought, and nobody asked how the room would be used or cleaned.
We think epoxy is the grout to plan for when a joint will see water, staining or heavy use. It gives homeowners a joint that stays the color they picked, and it gives property managers a floor with fewer callbacks. The part that makes it work is the planning: the right setting materials, the right color, the right joints left for flexible sealant, and an install crew that knows the clock.
That’s why we start with a consultation, in the showroom or remotely, and why we can send samples home so you can see tile and grout color in your own light before you commit. Builders and designers get detailed written quotes and logistics help so the material arrives when the crew is ready.
Northern Lights Design Team
Get the tile, grout and setting materials from one place
We supply tile and stone, setting materials, and the grout and finishing products that go with them, for homes and commercial buildings across the region. Start with our tile and stone selection, or browse the setting materials in our pro shop if you’re lining up a crew. Builders and property managers can go straight to commercial procurement.

FAQ
What is epoxy grout for tile?
Epoxy grout is a grout made from epoxy resins and a filler powder, mixed from two or three parts on site. It cures into a hard, non-porous joint that resists stains and water and does not need sealing. It is held to the ANSI A118.3 standard in the United States.
Can you use epoxy grout on floors?
Yes. Manufacturer data sheets list epoxy grout for ceramic, porcelain, quarry and natural stone tile on interior and exterior floors, including high-traffic commercial areas. Check that the specific product suits the tile, the cleaning method and the environment, and keep movement joints filled with flexible sealant.
Will epoxy grout crack?
In the field of the tile, epoxy is designed not to shrink, crack or erode. Cracking happens where it is used in corners and change-of-plane joints, which should hold flexible sealant instead, or over a flexing subfloor. Build the substrate to the tile standard and the joints stay intact.
How long before you can walk on epoxy grout?
It depends on the product, but one manufacturer calls for keeping traffic off for at least 24 hours after setting and protecting the installation for at least 7 days. Another lists foot traffic at about 24 hours and full service at 10 days. Follow the data sheet for your product, and contact us if you want help matching the grout and schedule to your project.
Sources
- Epoxy Mortar, Tile Council of North America
- Choosing the Right Grout: Cement vs. Epoxy
- Epoxy Grouts FAQ
- Kerapoxy product data sheet
- EzPoxy EzClean technical data sheet
- SikaTile-825 Epoxy Grout
- Epoxy Grouting, Fine Homebuilding
- Why Epoxy Grout Should Never Be Used in Shower Corners and Movement Joints
